Aston Martin, Jaguar, Audi, Ford. x1 Tiny Head Laser Jammers uk.

Like if this guide is helpful
Link to an eBay page Remove
Add up to 3 more photos
Link to an eBay page

Ingenious Tiny Stand Alone Jammers for far less Cash.

Jammers Work, Detectors Just Don't. Any Salesman that says they give you Proper Warning, or Braking Time are just Deceiving Consumers, and talking a load of Bollocks!.
With Dominant Lidar - Laser Guns. And the odd remaining Ka Radar Guns, Cops get your Speed in under 0.30 or 0.40 Seconds everytime.

All Police Lidar systems operate in a Sterile 905Nm 'Pulse free' Enviroment. Sharply Pulsed Infra Red Signals do Not occur naturally anywhere on Earth. This is what makes Lidar Systems easier to jam than most realise. Lidar Guns have an Exempelary Prosecution Record. Any Pulsed IR interference like a Jammer, & they do go into Error Mode  (EO2 or EO1 on L.T.I. Models), until a clean 'Legally firm' reading is attained.  We have seen this for Years in Jammer Test Videos.
Dragon Eye easily detects many Jammers I.C. Oscillator Generated Jam Waves. It may not recognise the flexible-different HP-M60 Signals?. Video on DIY methods Here.

Only I today use the superb 75 Watt Laser Diode. Datasheet. ​I could use a Cheapo 10 Watt Laser running at 20% Power, and then dress it up my Units with Bullshit Decals as Blinder ALP Stinger & others.
Fact remains Slick talking Salesmen, Chromed ALP Stickers or Fancy LED displays won't ever Save you a Ticket.

Laser Jammer  Emission using an Infra Red Camera (Cabin Alert on Right)..
Link to an eBay page Remove
Add up to 1 more photo
Link to an eBay page
Paste a YouTube Video URL
Uploading...
Uploading...
Laser Jammer  Emission using an Infra Red Camera (Cabin Alert on Right)..
Link to an eBay page Remove
Add up to 1 more photo
Link to an eBay page
Laser Jammer  Emission using an Infra Red Camera (Cabin Alert on Right)..
Link to an eBay page Remove
Add up to 1 more photo
Link to an eBay page
Paste a YouTube Video URL
Uploading...
Uploading...
Laser Jammer  Emission using an Infra Red Camera (Cabin Alert on Right)..
Link to an eBay page Remove
Add up to 1 more photo
Link to an eBay page
Laser Jammer Emission using an Infra Red Camera (Cabin Alert on Right)..


My Jammer's Primary Features.

Black Small Unit 50mm x 35 x 20mm 25/32 Inch Thick, every Unit is IR-hand Tested.
​LED Alert Model has a Second wired Box as shown. Wires for Power & LED can be cut or extended & Insulated at will.

Jams all Contemporary Lidar Guns, possibly also the Rare VPR Models.  Most places and States are using Pro Laser 3-4. Europe Italy Germany UK mainly entirely LTI Models.
 SPLPL90-3 75 Watt Laser is only used. Capable of up to 90 Watts in bursts see Manufacturers Graph, but set sensibly lower for reliability.   I won't compromise as other Makers  do using a  Cheap 10Watt Laser.
Sealed from Damp-Water Ingress. Ever Unit is sealed with Resin so there are no Voids for Snow Road water to Enter. Blinder and Laser Interceptor have both suffered this problem.
 Immune from Sunlight. Or D.C. shift as known it in Electronics. Blocked in 3 different ways, with this Design, so no Falsies at all from burning Florida or Australia Sunlight with these.
 Optimum Sensitivity With U.S. or Germany Retailer Purchased  905Nm Photo-sensor, optimum Efficiency achieved with my own Research / Experiments. Ultra sensitive to the already very Pervasive Spiked Lidar Gun Signals. On Standby it uses just 0.000006 Amps, almost nothing.
  Just 2 Power wires to connect.  Connects direct to Battery or Fusebox or Switch as mentioned . On standby uses 6-8  Microamp, Millionth an Amp until triggered, then up to 0.4 Amps Max. Just mount it secure horizontal & discretely, ideally close to front or rear Number plate. Front is Targeted in 90% occasions. 
 Simple cheap DIY mounting. Use One tie Wrap between Laser & Sensor. A small Angled bracket or just Superglue directly onto Grill Plastics. Drill x2 6mm holes and can go behind some Badges, any Black Plastic mounting plate, under License plate, Set in the Foam behind Bumpers Skirts. Velcro 3M tape and Super Glue have all be been used with good results.
Every single Unit is Made here in U.K. Oscilloscope Hand Tested during Assembly, for correct function before sealing. This way I & the Customer know a Jammer is working perfectly before Dispatch.
​Obviating the need for any model of 'Hazardous' D.C. Signal  AL, LI, ALP 905 or other DC Signal  'Jammer Destroyer Tester's'.
Have something to share? Create your own guide... Write a guide
Explore more guides