eBay
  • Daily Deals
  • Collections

Fiat Key Programming / Reprogramming

stusellingonly
By Published by

Hello everybody.

Firstly, I must apologise to all those who have purchased these instructions from me over the past few months.

From May this year, Ebay revised their Downloadable Media Policy & decided to ban all digitally delivered items. This meant that the instructions that I have been successfully emailing to people were now banned from being delivered by email. I could have elected to print each set out & post them to buyers, but to be perfectly honest this would be both time consuming & an unnecessary use of resources (printer ink, paper, envelopes etc.) so I decided to simply stop listing in order to be a good boy & comply with the policies.

Unfortunately, not all members are as good at sticking to the rules as myself & several are still listing on a nudge, nudge, wink, wink, "I won’t actually state that I email the instructions even though I do" basis. This guide is dedicated to these members.

It would seem that the only way to make sure everybody sticks to the rules is to make sure that the information is made available to all, so rather than paying for the instructions to be emailed, here they are for free:

Seicento

1. Firstly obtain the 4 digit security code for the vehicle

2. Press the button (in the interior light assembly there is a button and an LED next to the alarm ultrasonics) for about a second and the LED will flash.

3. Release the button

4. After approx 5 seconds the LED will flash once

5. Enter the first digit of the security code using the button as above.

6. Wait for about 5 seconds and the LED will flash once. Enter the second digit of the security code as above - if one of the digits is a zero, do not press the button at all and wait for the single flash requesting the next digit.

7. If all the numbers are entered correctly the LED will flash for 10 seconds Whilst the LED is flashing, press and hold the button near the interior light (used above) The LED will continue to flash until you press a button of a remote - it should then remain on.

8. Release button of remote and the one in the interior light.

9. Repeat for subsequent remotes

Cinquecento

1. Firstly obtain the 4 digit security code for the vehicle

2. Press the button (in the interior light assembly there is a button and an LED next to the alarm ultrasonics) for about a second and the LED will flash.

3. Release the button

4. After approx 5 seconds the LED will flash once

5. Enter the first digit of the security code using the button as above.

6. Wait for about 5 seconds and the LED will flash once

7. Enter the second digit of the security code as above - if one of the digits is a zero, do not press the button at all and wait for the single flash requesting the next digit.

8. If all the numbers are entered correctly the LED will flash for 10 seconds whilst the LED is flashing, press and hold the button near the interior light (used above)

9. The LED will continue to flash until you press a button of a remote - it should then remain on.

10. Release button of remote and the one in the interior light.

Bravo/Brava

1. Firstly obtain the 4 digit security code for the vehicle

2. Press the button (in the interior light assembly there is a button and an LED next to the alarm ultrasonics) for about a second and the LED will flash.

3. Release the button

4. After approx 5 seconds the LED will flash once

5. Enter the first digit of the security code using the button as above. Wait for about 5 seconds and the LED will flash once

6. Enter the second digit of the security code as above - if one of the digits is a zero, do not press the button at all and wait for the single flash requesting the next digit.

7. If all the numbers are entered correctly the LED will flash for 10 seconds

whilst the LED is flashing, press and hold the right hand button near the

interior light (used above)

8. The LED will continue to flash until you press a button of a remote - it will

then remain on.

9. Release button of remote and the one in the interior light.

Coupe/Barchetta

1. Firstly obtain the 4 digit security code for the vehicle

2. Press button (in the interior light assembly there is a button and an LED next to the alarm ultrasonics) for about a second and the LED will flash.

3. Release the button

4. After approx 5 seconds the LED will flash once

5. Enter the first digit of the security code using the button as above.

6. Wait for about 5 seconds and the LED will flash once

7. Enter the second digit of the security code as above - if one of the digits is a zero, do not press the button at all and wait for the single flash requesting the next digit.

8. If all the numbers are entered correctly the LED will flash for 10 seconds whilst the LED is flashing, press and hold the right hand button near the interior light (used above)

9. The LED will continue to flash until you press a button of a remote - it will then remain on.

10. Release button of remote and the one in the interior light.

Ulysse

New remotes cannot be programmed without the use of diagnostic equipment but existing remotes can be synchronised as follows:

1. Switch on the ignition

2. Press the lock or unlock button and hold for 10 seconds.

Scudo

New remotes cannot be programmed without the use of diagnostic equipment but existing remotes can be synchronised as follows:

1. Switch on the ignition

2. Wait for the system LED to extinguish

3. Press the lock or unlock button and hold for 10 seconds, do this on all remotes to synchronise them.

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

 
Write a guide
Explore More
Choose a template

Additional site navigation