Understanding & Fitting the JAGO Net Rod System for Bay Windows

Like if this guide is helpful
Edit Link Remove
Add up to 3 more photos
Add a caption

Decozo Workroom Supplies offer The JAGO Net Suspension System as it is a great solution for virtually any window and is easily fitted or removed when cleaning. The kit contains everything you need for  straight runs or bay window up to 5 meters.
Curved Bays - For sweeping curves use the solid connectors to join the bay rods. After fitting, the ends can be marked to create the desired finished length. The finished rod will bend to follow the shape of your window without kinking. Space support brackets evenly around the window as shown in the examples picture.

Angled Bays - For all angled bays cut the rods to fit each section of the window frame and use the flexible connectors at each junction. These connectors can be folded by hand to match required angles, and will ensure the rods run parallel to the window frame when fitted. Place brackets each side of the joint for maximum support as shown in the example pictures.
The 5m Net Rod Kit Contains:
Link to an eBay page Remove
Add up to 3 more photos
Add a caption
Link to an eBay page

Support Brackets

Face Fixing Support Bracket (0108) Locate on the front of the window frame and secure with screws, making sure the screw heads are below the surface.
Side and Top Fixing Support Bracket (0108)
Alternatively the bracket can be fitted using the side screw holes provided.
Adhesive Pads -
  1. Clean both surfaces where pads are to be used with methylated spirits only ( do not use any other cleaner like white spirit or nail polish remover etc.) Allow surfaces to dry.
  2. Stick adhesive pads to bracket surface.
  3. Remove liner from adhesive pad before applying to window. Press firmly in position and allow 20 minutes before hanging curtain.
Please Note: Adhesive pads will perish with age and will need replacing with JAGO accessory 0110.
Link to an eBay page Remove
Add up to 3 more photos
Add a caption
Link to an eBay page

Connectors

Solid Connector (0107) - Use solid connector to join track together for bow windows. See example 1. Push firmly up to shoulder.
Flexible Connector (0106) - A flexible connector must be used for each angle in bay windows. (as shown in example 2, 3 & 4). To fit, push ends into track as solid connector.

Link to an eBay page Remove
Add up to 3 more photos
Add a caption
Link to an eBay page

Supports

Flexible Track End Supports (0111)
The end supports have been designed to allow for a small length adjustment. Fit to bracket as shown.
Mid Support (0109)
The mid supports have been designed to snap over the curtain heading.

Link to an eBay page Remove
Add up to 3 more photos
Add a caption
Link to an eBay page

Fitting Instructions

Example 1
  1. Fix brackets at each end of window. Fix remaining brackets approximately 62cm (2ft) apart.
  2. Use solid connectors to join track.
  3. Place assembled track on brackets. If track is excessively long, remove one end support, mark and cut off required amount using a junior hacksaw. Refit end support.
  4. Slide rod through net curtain header, snap on mid supports (see illustration) at same interval as fixing brackets and hang in position.
Example 2
  1. Fix brackets at each end of window. Fit brackets approximately 15cm (6ins) either side of each angle in window.
  2. Using a junior hacksaw, cut five lengths of track to suit window sections. Use four flexible connectors to joun lengths formig a track to fit bay window shape.
  3. (a) Slide on end fittings (0111)
    (b) Slide rod into net curtain header.
    (c) Snap on mid support (0109) onto rod in required positions over curtain header on rear (see illustration mid supports).
  4. Hang assembled track on brackets.
  5. Slide rod through net curtain header, snap on mid supports (see illustration) at same interval as fixing brackets and hang in position.
Follow instructions of example 2 for example 3 & 4.
Accessory Packs Available Decozo Workroom Supplies offer a wide range of quality products for Curtain Makers, Soft Furnishers, Interior Designers and the General Public undertaking home improvements.
Call for more details: 0115 941 2274 (Mon-Fri 9-5)
Have something to share, create your own guide... Write a guide
Explore more guides