|
HTML clipboard

or 
Direct Hard Wire SMART Cord with Round or Flat MUTE Button Kit
Brand New straight from the manufacturer with instructions
and a 1 year warranty!
Direct
SMART Cord with MUTE Button FOR YOUR RADAR DETECTOR
Quantities are limited. No one else has these, be the first!
Direct Hard Wire Power Cord comes with a built-in FUSE to protect your investment.
The Direct SMART Cord with Round or Flat
MUTE Button accessory is a unique power cord with a convenient
MUTE BUTTON right within arms reach!
Tired of dangling power cords? Our direct cords eliminate the bulky dangling power cords that hang over your dashboard and over your rearview mirror.
We usually ship the same day so you get your order with lightning fast shipping!
|
What is a Direct SMART Cord with Round or Flat MUTE button? |
The Direct Wire SMART Cord is an optional accessory that allows you to connect your radar detector directly to your fuse block or other 12-volt source
(leaving your lighter socket free for other uses) and provides a MUTE button for the detector.
The Direct Wire SMART Cord is approximately
8 feet long and comes with a built-in LOW AMP FUSE
to protect your radar detector.
Be Safe with Safe-N-Sound1 products that come with a low amp fuse, guaranteed to protect your equipment.
It's the perfect addition for any car when reaching the detector's mute button on the windshield is a stretch.
Normally comes with a T - Tap to connect to a power wire source like below.
Just wrap the t-tap onto the wire and pinch
with a pair of pliers, then you just connect the red wire to the t-tap.

If you would like to change the t-tap to one of the fuse taps, just let us know which one you would like by leaving a note with your PayPal payment AND email us
1. Blade Fuse Tap to connect to a blade fuse
in the fuse box

2. Mini Blade Fuse Tap to connect to a mini blade fuse
in the fuse box.

|
Here is a comparison of the
blade fuse on the left and the mini blade fuse on the right |

Now you can wire directly to your fuse box
and eliminate dangling power cords.
Our power cords will allow your radar detector to be hard wired to your vehicle very easily. If you do change vehicles, simply unplug the red wire from the T-tap connector or the Fuse tap, and unhook the black ground wire.
This kit will work on the below detectors that uses the "Modular" type power plug.
Beltronics models:
GX 65,
STi Driver,
Pro GX 65
Pro RX 65, Pro RX 55,
Vector 995, Vector 965, Vector 955,
Vector 940, Vector 895 & Vector 795 V6, V8


ROUND MUTE BUTTON:
-
Normally
the cord for the mute button is about 4 feet long. Figure out
where you would like to mount your mute button. The round mute
button needs a hole that is approximately 1/4" or 6.5mm to mount.
Try to test drill a hole onto an extra piece of plastic or wood that
is not needed to make sure the hole is sufficient.
-
Make
sure the chosen mounting location is either 1/8" or 2.5mm thickness or
less. Round mute button will not screw into a hole if the
mounting surface is any thicker.
-
Unscrew
the nut from the round mute button. Place the round mute button
through the hole from behind with the lock washer on it or after the
mounting hole. The lock washer is the round washer with the slit
in it, it is slightly curved up from each end. The lock washer
is needed so the nut will not loosen from vibration. Hold the
round mute button with one hand and hand tighten the nut onto the
round mute button on the front side of the mounting hole.
Finally tighten with a pair of needle nose pliers just until the lock
washer flattens.

FLAT MUTE BUTTON:
-
Normally
the cord for the mute button is about 4 feet long. Figure out
where you would like to mount your mute button. The flat mute
button has strong mounting tape on the back side of it. Mounting
on a smooth surface would be ideal.
-
Clean
the surface with rubbing alcohol or some sort of cleaning agent.
Let the surface dry, peel the backing off of the mounting tap and
apply pressure for a few seconds so the mounting tape will adhere
well.
----------------------------------------------------------------------------------------------------------------------------
New Direct SMART Cord with built-in FUSE and Mute Button
(let us know if you would like the Round or Flat Mute Button)
Detailed instructions to make your installation very easy
Wire ties to make your installation neat.
If you would like to change the t-tap to one of the fuse taps, just let us know which one you would like by leaving a note with your PayPal payment AND email us
1 year limited warranty at no charge.
Delivery Confirmation to track your order. (if available)
|
and
for $10.00
| |
----------------------------------------------------------------------------------------------------------------------------
|
Just check out our FEEDBACK and see what our customers had to say. |
 |
Very Satisfied Installed in 20 Minutes Quality Product Highly Recommend |
 |
Quickest ship ever! Thanks! A+++ |
 |
Super fast shipping, item as described, Highly recommended. A+++ |
 |
Good transaction - would buy from seller again |
 |
Lightning fast shipping. Thank you. Ebay rating: A+ |
 |
Fast shipping. Great Contact with my questions. Would buy from again!!!! |
|