Bidding has ended on this item.

Posts to:
Posts to:

Details about  Cornford Roadhouse 50 Watt All Valve Guitar Head

See original listing
Cornford Roadhouse 50 Watt All Valve Guitar Head
Item Ended
Item condition:
07 Jul, 2014 08:45:41 BST
Winning bid:
3 bids ]
May not post to United States - Read item description or contact seller for postage options. | See details
Item location:
Birmingham, United Kingdom


eBay item number:
Seller assumes all responsibility for this listing.
Last updated on  02 Jul, 2014 08:24:22 BST  View all revisions

Item specifics

Used: An item that has been previously used. The item may have some signs of cosmetic wear, but is fully ... Read moreabout the condition
Type: Guitar Amplifier
MPN: Roadhouse Brand: Cornford
Number of Channels: 1 Model: Roadhouse
RMS Power: 50

For sale is my Roadhouse 50 Head in full working order. I purchased this 2nd hand off ebay and it came without original packing and footswitch. I believe generic footswitches are available. Not getting much use now so has to go. These amps are becoming hard to find now. Happy for buyer to collect or meet half way for fuel cost up to 50 miles from Birmingham.

 Details from website:

The Cornford Roadhouse Series of amps comprises 4 models - the Roadhouse 30 1x12" combo and amplifier head and the Roadhouse 50 2x12" combo and amplifier head (featured on this page). 1x12", 2x12" and 4x12" matching speaker cabinets are also available to complete the range.Featuring top quality PCB design and still constructed and handwired in the UK, these amps represent the ultimate affordable price point for Cornford tone junkies.The Roadhouse 50 has the same basic circuit design as the Road House 30, but with grid biased output stage and bigger transformers for those extra decibels!

The Roadhouse 50 is a more brutal version of its 30-watt sibling. dhuse - Story

The Cornford Roadhouse Series of guitar amplifiers are stripped down and simple to operate: simple yet very versatile.

The Roadhouse 30 Head and 1x12 Combo offer a combination of enough power to cut through a mix but with a power amp design that can be pushed into overdrive, giving touch sensitivity and harmonic richness without too many decibels!

The Roadhouse 50 Head and 2x12 Combo offer more of the above but with a little extra power, for those players that need extra punch; the Combo also having the extra 12” Celestion Vintage 30 to shift more air!

"Point to point hand wiring an amp takes a long time and as such, the cost of the hand wired Cornfords will put them out of reach of many players. The design team at Cornford began planning a PCB (printed circuit board) valve amp quite a while ago, and have taken the time to ensure they get the design right and find the right company (also UK based) to manufacture the boards for them. Whilst there is still something special about the hand wired amps (we don't know what exactly, we just call it "Mojo"!), Cornford have managed to design and produce a PCB based tube amp that creates some fantastic tones, has almost no background noise (a good sign that the components have all been well placed and shielded on the PCB), uses the same cabinet construction and speakers as the hand wired amps, and yet is less than half the price of the equivalent hand wired model.

If you're looking for a mid priced, gigging, tube amp we can't recommend the Roadhouse range enough - it really is that good. We just hope that Cornford can keep up with the demand.

Roadhouse 50 - Specification


Fixed bias, valve guitar amplifier head and 2 x 12 combo. One channel with footswitchable boost.


50 Watts.


2 x 6l6


3 x 12AX7.


From left to right:
Input (1 megohm impedance. Suitable for guitars with most types of pickup. The amplifier may, in general however, not give good results with the types of pickup associated with acoustic instruments); Gain (this controls the amount of preamp gain and hence level of preamp distortion in the amplifier); Boost (this controls the amount of extra signal sent to the preamp from the first gain stage and the amount of extra distortion in the preamp. This function is useful for heavier rhythm and lead guitar playing); Bass (this controls the low frequency response of the preamp); Middle (this controls the midrange frequency response of the preamp); Treble (this controls the high frequency response of the preamp); Send (this socket sends a low level signal (-6dBV) from the preamp suitable for driving effects pedals or rack processors); Return (the output signal from your effects units is reintroduced back into the amplifier's signal path after the preamp, via this socket); Master (this controls the overall output level of the amplifier and should be adjusted to suit your playing environment); Mains/Standby (this is a 3-position toggle switch. In the ‘Off' position, no mains power is sent to the amplifier's circuitry. In the ‘Standby' position, the low voltages are switched on and the valve heaters are allowed to warm up before the high voltage is applied to them - allow 30 seconds or so in this position to prolong valve life. In the ‘On' position, the amplifier is ready to play).


From left to right:
Mains inlet socket (this accommodates a standard IEC mains lead. The mains fuse is contained within a drawer in this socket and should always be replaced with a fuse of exactly the same type and rating to reduce the risk of fire or electric shock); High Tension Fuse Holder (this accommodates the high voltage fuse for the amplifier. If it fails, this may indicate that the output valves have developed a fault. Once again, as with the mains fuse, it must be replaced with a fuse of the same type and rating); Speaker Sockets (there are a total of 5 speaker sockets: one is connected to the 16 ohm tap, two are connected to the 8 ohm tap [this will accommodate two 16-ohm speakers or one 8-ohm speaker] and two are connected to the 4-ohm tap [this will accommodate two 8-ohm speakers or one 4-ohm speaker]. It should be noted that only one output tap should be used at any one time. That is to say a speaker load may only be connected to the 16-ohm socket, or one or both 8-ohm sockets, or one or both 4-ohm sockets. No other combination should be connected). NB: To avoid damage to your amplifier, always connect a speaker to the output before switching on; Footswitch Socket (this is used to connect the supplied footswitch to the amplifier for remote switching of the ‘Boost' function and overrides the front panel toggle switch).


All metal footswitch.


Series effects loop. Send level is a nominal –6 dBV. Send impedance is 33k ohms. Return impedance is 145k ohms. Suitable for foot pedals and rack processors.


Metal corner protectors; top carry handle (head); side metal bar handles (combo).


Quality PCB (printed circuit board) design. UK built.


Custom designed and built by one of the UK's leading manufacturers.


2 x 12" Celestion Vintage 30 (combo only).




All metal footswitch, to enable remote switching of the amplifier's ‘Boost' function..


19 mm, lock jointed ply (head) or pine (combo) covered in black ‘Lizard' vinyl with black grille cloth and white piping.


600 mm (W) 460 mm (H) 300 mm (D) (combo); ? mm (W) ? mm (H) ? mm (D) (head).


25kg (head); TBCkg (combo)

Questions and answers about this item

No questions or answers have been posted about this item.

Submit bid

Time left:
Current bid:
(Approximately ##1##)
Import charges:
Your maximum bid:
Your maximum bid:
Please read the full listing. By clicking Confirm bid you commit to buy this item from the seller if you are the winning bidder. You will enter a binding contract.
By clicking Confirm bid, you are committing to buy this item from the seller if you are the winning bidder and have read and agree to the Global Shipping Programme terms and conditions - opens in a new window or tab. Import charges previously quoted are subject to change if you increase you maximum bid amount.
Resume bidding, if the page does not update immediately.
Submit bid
Review and confirm your bid
Bid confirmation
Free P&P
See item description
(Approximately ##1##)
(Enter ##1## or more)
(Enter more than ##1##)
Your maximum bid:
Increase maximum bid
Submit bid
Confirm bid
Increase maximum bid
Change bid
, you've been outbid. Don't let it get away - bid again.
, you're the highest bidder on this item. Hope you win it.
, you're the first bidder. Hope you win.
, you're currently the high bidder, but you're close to getting outbid.
, this auction is almost over and you're currently the high bidder.
, you're the high bidder, but the reserve price hasn't been met.
Please enter your bid again.
Please enter a valid number as the bid price.
Enter an amount that is equal or greater than the minimum bid required. This can be found under the bid entry box.
Maximum bids can't be lowered once they're submitted.
This seller requires the buyer to have a PayPal account to purchase this item. Get a PayPal account here .
Your bid is greater than or equal to the Buy it now price. We recommend you purchase this item via Buy it now. If you still wish to bid, you may do so below.
Time left:
Current bid:
(approximately ##1##)
Your maximum bid:
(approximately ##1##)
Increase your maximum bid:
By clicking 1 Click Bid, you are agreeing to buy this item from the seller if you're the winning bidder. Learn moreabout 1-click bid - opens in a new window or tab
(approximately ##1##)
Winning bid:
Starting bid:
Congratulations The auction has ended and you're the winner.
The auction has ended, but the reserve price was not met.
Sorry, the auction has ended and you were outbid.
Good news, you're the highest bidder.
Sorry, you've been outbid.
You're the highest bidder, but the reserve price has not been met.
Please enter a higher amount than the current bid.
Maximum bids cannot be lowered once submitted.
Please enter a valid number.