Cramer Basin Bath Sink Enamel Repair Kit Alpine White

Material Composition: 2-component filler and hardener, 1-component repair spray.

Use: Repair of dented and chipped sinks, basins, shower- and bathtubs made of porcelain, ceramics and acrylic.

Material characteristics: With the Cramer Repair-Kit, damages can be repaired quickly and effortlessly. For professional repair work that requires simple use and shows perfect results.

Colour:

16080 Alpine White / European White

Intensity of Gloss: Gloss and Mat

Density: Enamel Spray: 0,80g/cm³ at 20ºC

Filler: 1,75g/cm³ at 20ºC

Hardener: 1,15g/cm³ at 20ºC

Use of solvents: Do not use thinner

Packaging: The Repair-Kit consists of:

111121 container of filler 30g

Tube of hardener 8ml

Aerosol spray can of enamel 50 ml

Spatula

Pieces of sandpaper for ceramics / enamel (brown)

Piece of sandpaper for acrylic (grey)

Storage: Minimum temperature: 5°C

Maximum storage temperature: 30°C, maximum short-term temperature: 40°C

Shelf life for an unopened kit in a dry and cool place: 2 years

Please follow local safety regulations.

Technical Information for Application

Application Surfaces: Steel, cast iron, ceramics, enamel, acrylics

Materials needed: Wire brush for rust spots

Acetone or thinner

Dust cloth

Paper and masking tape

Protective gloves and goggles

car polish (if needed)

Preparatory work: To achieve perfect results and durability, it is vital to clean and prepare the work surface thoroughly. Please read the technical information provided in this leaflet carefully before starting the repair.

Remove rugs, towels, shower curtains etc. from your work area.

Mask an area of 20 cm around the damaged spot with newspaper and masking tape.

Surface Preparation Please wear regular household gloves and goggles for the following steps:

Remove rust spots and loose particles with wire brush. Do not sand the surface.

Then, clean damaged area with grease-free acetone or thinner.

Work with Spatula: Please wear household gloves for the following steps:

Only take as much filler as needed from the container and mix thoroughly with a small amount of hardener on a sheet of paper. Mixing ratio should be 30 parts of filler and 1 part of hardener.(walnut amount of filler to a pea amount of hardener). After mixing, spread the mixture thinly on the paper to remove any air bubbles. Then lift the solid mix with the spatula.

Apply mix on the damaged area and smooth it with spatula. Application time: approximately

three minutes. When working with porcelain, you can reinsert any of the chipped porcelain pieces. Let the area dry and harden for about 30 minutes. Then, sand down any uneven spots and remove the sanding dust. No ridges or holes should remain.

When working with acrylics or fibreglass please note the following differences:

The filler can only be used for the repair of chipped areas or deep scratches. Tension cracks or broken out areas cannot be glued. After filling the chipped or scratched area, sand down with the 800-grit wet sandpaper (grey) with water.

Spray work: Please wear household gloves for the following steps:

Shake spray can vigorously for three minutes before use. Try out on a sample area first.

Apply spray thinly from a distance of about 15-20cm. Using a mask from a paper- or cardboard cut-out will facilitate smooth application (cut-out size should be similar to that of the damaged area). Hold mask about 1-2cm above damaged area while starting to spray on the paper/cardboard first and then moving across the cut-out to cover the damaged area. Apply second coat after one minute. Repeat until damaged area has been fully covered.

Hint: You can remove spots of spray applied too thickly spray (e.g. drips) with grease-free acetone. The colour hues are based on original colours provided by the manufacturers of bathtubs etc. Application with acrylic products may show slight variations.

After repair: The finished surfaces should not be exposed to water for four days, so it can harden 100%. The repaired area can be polished with regular car polish after hardening.

Capacity: The repair material can be used for 5 average-sized repairs.

Workability: Please make sure rooms are well ventilated.

Application temperature of filler: 15ºC min.

Application temperature spray: 20ºC min