Details about Cuprinol Anti-slip Decking Treatment Natural clear 2.5lSee original listing
31 Mar, 2011 16:27:50 BST
London, United Kingdom
Cuprinol Anti-Slip Decking Treatment is a clear, natural matt finish that helps
make decking safer especially when wet by improving slip-resistance.
Cuprinol Deck-GripTM Microbead technology gives a non-abrasive, anti-slip
finish, whilst powerful algicides help protect the film from the growth of green
algae and mould. Cuprinol Anti-Slip Decking Treatment also provides a water
repellent finish that seals and protects. It is ideal for use on decks that are
partially shaded and in preparing decks for the winter
Where to Use – Cuprinol Anti-Slip Decking Treatment is suitable for use on
all types of new or used bare and stained timber decking. Certain penetrating
finishes such as Cuprinol Decking Oil, Decking Seal and Decking Protector
(DP) will need to be weathered prior to the use of Cuprinol Anti-Slip Decking
Treatment. If in doubt try a test area first for appearance and adhesion or
Spreading Rate – This 2.5 litre pack is normally sufficient for 30m² with 1
coat. It is important that this coverage rate is achieved in order to provide the
necessary anti-slip properties, do not brush out too thinly. More than one coat
may be necessary in some cases. Absorbent wood, swan wood and grooved
decking will reduce coverage.
Preparation – All surfaces should be clean, dry and sound. Timber
specifically sold for decking is normally pre-treated with wood preserver to
prevent decay. Untreated timber not in ground contact should be treated with
Cuprinol Trade Wood Preserver Clear (T) and allowed to dry for 3-5 days
before using Cuprinol Anti-Slip Decking Treatment.
Bare Wood: clean off any dirt, mould or algae using Cuprinol Decking
Cleaner. Rinse off with water and allow to dry before applying Cuprinol Anti-
Slip Decking Treatment.
Presealed Wood: Decking previously treated with Cuprinol Decking Oil,
Decking Seal or a similar penetrating treatments should be allowed to weather
for at least 6 months before applying Cuprinol Anti-Slip Decking Treatment.
Before application, clean surfaces as for bare wood. Decking coated with
sound decking stain should be washed with Cuprinol Decking Cleaner to
remove any surface dirt and allowed to dry.
Weathered Wood: Completely remove all grey wood by sanding back to a
clean sound surface or by using Cuprinol Decking Restorer.
Painted/Varnished Wood, Stains in Poor Condition: Sand-off or chemically
remove existing coating and then treat as bare wood.
Application – Stir well before and occasionally during use. Apply using a
brush or roller. Brush or roll out any accumulations on the surface of the
Cuprinol Anti-Slip Decking Treatment is white on application but dries to a
clear matt finish. Do not apply if rain is likely before the treatment can dry, if
the temperature is below 5ºC or in conditions of high
humidity or frost.
Touch Dry - 2-6 Hours
Recoat – When previous coat is fully dry
Cleaning and Storage – Remove as much product as possible from
application equipment before washing out with water. Reseal container after
use. Wash off any splashes with water while still wet. Do not use or store in
extremes of temperature and protect from frost.
Aftercare – This is not a non-slip product. The anti-slip properties will be
reduced if decks become dirty, dusty or leaves and decaying vegetation are
allowed to accumulate. Clean the treated decking periodically using Cuprinol
Decking Cleaner to avoid any reduction in performance and depending on
wear, re-treat with Cuprinol Anti-Slip Decking Treatment to maintain the antislip
UK mainland only
Powered by eBay Turbo Lister
Return policy details
Most purchases from business sellers are protected by the Consumer Contract Regulations 2013 which give you the right to cancel the purchase within 14 days after the day you receive the item. Find out more about your rights as a buyer - opens in a new window or tab and exceptions - opens in a new window or tab.