Details about Crown CE 1000 Professional Power Amplifier 1100WCrown CE 1000 Professional Power Amplifier 1100W See original listing
26 Aug, 2012 19:10:58 BST
[ 0 bids ]
Norwich, United Kingdom
This is a Crown CE 1000 1100W professional power amplifier, in good working order and good physical condition. It was used to power the midrange speakers in a three-way setup but would be equally well suited for bass or any other demanding professional sound application. Anyone in the industry will know that Crown amps are some of the best and can go all night without problem.
Full specifications here: http://www.iceco.com/Crown/CE1000.pdf
The amp is currently in Norwich and can be collected (cash only for collection) or can be sent by courier but this will be quite expensive as it's so heavy.
If you have any questions please just message me.
I'm clearing out all of my sound equipment due to not having enough time to run my sound system any more - check out my other listings if you're interested!
The CE-Series of Crown amplifiers are professional tools designed and built for
professional use. Engineered and manufactured by the same teams who built
Crown’s acclaimed Macro-Tech®
and KSeries amps, the CE 1000 has the rugged
heart and soul that have characterized
Crown’s amplifiers for over 30 years.
With many of the same controls and features
you’ve come to expect from Crown, CESeries amplifiers feature front-panel detented
level controls, useful function indicators,
proportional fan-assisted cooling, shortcircuit protection and more.
For superior flexibility, Crown CE-Series
amplifiers can work with a range of Crown
SST (System Solution Topologies) modules
which provide true professional features like
fixed-point crossover and summed bass
With a powerful, reliable performance, CESeries amps easily handle real 2-ohm loads
and are capable of chest-thumping lows.
Plus, your investment in an CE-Series amplifier is backed by Crown’s unequaled ThreeYear, No-Fault, Fully Transferable Warranty
that covers everything.
For more details about the Crown CE-Series,
contact the Crown Technical Support Group
at 800-342-6939 or 219-294-8200. Also,
visit the Crown Audio website at
Note: All measurements relate to 120-volt, 60-Hz units in
Stereo mode with 8-ohm loads and an input sensitivity of 26-
dB gain at 1-kHz rated power unless otherwise specified.
Specifications for units supplied outside the U.S.A. may vary
slightly at different AC voltages and frequencies.
Load Impedance: Safe with all types of
loads. Rated for 2, 4 and 8 ohms in Stereo
mode, 4 and 8 ohms in Bridge-Mono mode.
Voltage Gain to 1-kHz, 8-ohm rated output:
30.5-dB gain at 1.4-volt sensitivity;
26-dB gain at 2.34-volt sensitivity.
Required AC Mains: 50/60 Hz (North American units are 60 Hz only); 100-, 120- and
230-/240-VAC (±10%) units are available.
AC Line Current,
100 Volts: 7.6 A;
120 Volts: 6.3 A;
230-240 Volts: 3.5 A;
At Idle: All amps draw no more than
AC Line Connector: NEMA 5-15P (15 A).
Frequency Response: ±0.2 dB from 20 Hz to
25 kHz at 1 watt.
Phase Response: ±15 degrees from 20 Hz to
20 kHz at 1 watt.
Signal to Noise Ratio,
Better than 105 dB below rated 1-kHz
20 Hz to 20 kHz:
Better than 100 dB below rated 1-kHz
Total Harmonic Distortion (THD): 0.5% or
less true THD from 20 Hz to 20 kHz.
Intermodulation Distortion (IMD): (60 Hz
and 7 kHz at 4:1) Less than 0.1% at rated
power to 35 dB below rated power at 8 ohms.
Damping Factor: Better than 400 from 10 Hz
to 400 Hz.
Crosstalk: Greater than 55 dB below rated
power, 20 Hz to 20 kHz.
Common Mode Rejection (CMR): Better than
70 dB from 20 Hz to 1 kHz.
DC Output Offset (Shorted Input): ±10 mV.
Controls and Connectors
Level: A detented rotary level control for each
channel located on the front panel.
Power: An on/off rocker switch located on the
Mode: A two-position switch located on the
back panel below the input connectors which,
when turned to stereo, operates the amplifier
as two independent channels. When “BridgeMono” mode is selected, the amplifier bridges
the two output channels for twice the output
Reset: A front-panel push button used to
reset the circuit breaker that protects the
Sensitivity: A two-position switch located on
the back panel next to the Mode switch.
Switchable between 1.4 volts for full output
into an 8-ohm load (default setting), or a fixed
voltage gain of 26 dB. 0.775-volt sensitivity
available as a Service Option.
Fault Jack: A back-panel RJ-11 jack that may
be remotely monitored to signal amplifier
Fault condition. An LED or other signalling
device (not supplied) may be used.
(all located on front panel)
Signal: A green LED for each channel which
flashes when a very low-level signal (>–40
dBm) is present at input. May be used for
troubleshooting cable runs.
Clip: A red LED for each channel which turns
on when distortion becomes audible in the