Skip to main content
enterprise-island

enterprise-island

552 items sold
13 followers
Contact

All items

See all

About

Location: United KingdomMember since: 15 Oct, 2000

Feedback ratings

Last 12 months

Positive73- positive Feedback in last 12 months
Neutral1- neutral Feedback in last 12 months
Negative0- negative Feedback in last 12 months

Detailed seller ratings

Average for the last 12 months

Accurate description
4.9
Reasonable postage cost
4.9
Delivery time
5.0
Communication
4.9

All Feedback (1,389)

shirley9293 (177569)- Feedback left by buyer.
Past 6 months
Verified purchase
Good buyer, prompt payment, valued customer, The Gasket Shop
ian_mall (1190)- Feedback left by buyer.
Past 6 months
Verified purchase
Good buyer, prompt payment, valued customer, highly recommended.
ukfab12 (54165)- Feedback left by buyer.
Past 6 months
Verified purchase
Good buyer, prompt payment, valued customer A+++
buy_gadgets (1279398)- Feedback left by buyer.
Past 6 months
Verified purchase
fast payment, valued customer, pleasure to deal with. Thank You buy_gadgets
a***a (208)- Feedback left by buyer.
Past 6 months
Verified purchase
Excellent little tool. Thank you so much for inventing it. Parcel was very well wrapped and communication was excellent.
6***8 (221)- Feedback left by buyer.
Past year
Verified purchase
Product as described, prompt delivery, excellent transaction.
See all Feedback
Reviews (3)
MEYLE Radiator Cooling Fan Temperature Switch 100 959 0002 FOR 900 9000 Passat G
30 Aug, 2023
Meyle Rad Fan Temp Switch for VW Passat etc used in a TVR Chimaera
I bought a similar product for my TVR Chimaera from a reputable TVR parts reseller and when tested prior to fitting instead of switching at 92C it actually came in mid 70s - much lower than the cut out temperature. Consequently the cooling fans were pretty much permanently on. I selected this one because it was branded. I needed a switch that would turn on at 92C and off at 87 (as per TVR Spec) has an M22 thread with standard 6.3mm Lucar connectors (I could easily work around teh connectors if required). This met all of the requirements. Once installed I inserted a temperature probe into the cooling swirl pot that was connected to a Fluke 170 DVM I then run up the engine comparting the coolant temperature with that seen in RoverGauge from the ECU temperature sender. I could only do this up to about 50C because the coolant was expanding and would very soon overflow. Never the less at this point the ECU sensor was very close the the calibrated Fluke Fluke=52.4C ECU=53C. I removed the fluke sensor and reinstalled the coolant swirl pot cap. I left the engine running for several cycles of the cooling fans. The turn on point on the ECU sensor was generally 91C and off was generally 84-85C. Now I think that is pretty close for a 92-87 sensor . Clearly the measurements are a tad crude but certainly satisfy my requirements and the results are much better than a similar unbranded product from a respectable outlet. I have added a photo of the crude baseline calibration test of the ECU sensor showing the Fluke reading and the Rover Gauge reading
USPro 6pc Long Triple Square Socket Bit Set XZN Mercedes/VW M6- M16H 3228
07 Aug, 2019
Triple Square XZN bits for Porsche rear calipers
Exactly what I need to remove the rear calipers and disks from a Porsche Cayenne S Excellent value.
CARDALE CD45 Hex Cones CABLES lift Wires Garage Door Spares Apex Wickes Repair
22 Dec, 2018
Excellent repair kit for my elderly Cardale doors.
On my doors there is a hole to insert a pin to lock the spring rather than using Mole grips. I found this hole by looking at the instruction sticker on the garage door. I also had challenges removing the cones as my door is recessed in a brick reveal. Using the locking pin method made it easy to unbolt the spring mechanism from the surround and hinge it forward whilst the door is closed. Using the mole grip method I believe it would not have been possible to change the cones in this manner. I believe the Pins are inserted as shipping retainers to maintain the spring tension before installing. Overall very pleased with the product and the value for money.
See all reviews