Jenvey

Jenvey Throttle Bodies provide the ultimate induction solution. Jenvey DCOE Twin 48mm Throttle Bodies Body (Pair). Subject to the following conditions This does not affect your statutory rights.

Jenvey Throttle Bodies provide the ultimate induction solution. Jenvey DCOE Twin 45mm Throttle Bodies Body (Pair). Subject to the following conditions This does not affect your statutory rights.

Jenvey Throttle Bodies provide the ultimate induction solution. Jenvey DCOE Twin 50mm Throttle Bodies Body (Pair). Subject to the following conditions This does not affect your statutory rights.

A kit for the Renault Clio 2.0 16 v.172, 182 and RS models which contains Four SF48mm tapered throttle bodies. This does not affect your statutory rights. Subject to the following conditions 90mm long airhorns.

Throttle Linkage and Tie Rod - TB002 & TB003. Throttle bodies - MG023. Throttle Position Sensor - MG003. Fuel Pressure Regulator and Housing - TB006. This kit includes Subject to the following conditions.

Jenvey Throttle Bodies provide the ultimate induction solution. Jenvey DCOE Twin 42mm Throttle Bodies Body (Pair). Subject to the following conditions This does not affect your statutory rights.

Jenvey Renault Clio 172-182 RS Inlet Intake Manifold (MR23). A aluminium inlet manifold for the Renault Clio 172-182 cylinder head. This manifold uses SF bodies. Open Mon - Fri 8.30am - 5.30pm.

This manifold is designed for the standard Weber/Jenvey DCOE mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between Bodies 2-3 is 93mm, however this can be adjusted if required (depending on your linkage).

This manifold is designed for the standard Weber DCOE Carb mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between carbs 2-3 is 93mm, however this can be adjusted if required (depending on your linkage).

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold is designed for the standard Jenvey/Weber DCOE mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between throttle bodies 2-3 is 93mm, however this can be adjusted if required (depending on your linkage).

This manifold is designed for the standard Weber DCOE Carb mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between carbs 2-3 is 100mm, however this can be adjusted if required (depending on your linkage).

TIG welded in aluminium and fully internally ground to ensure optimum flow and performance. This manifold is designed for the standard Jenvey/Weber DCOE mounting and can be made with 40mm, 45mm or 48mm bore mounting plates.

This manifold is designed for the standard Jenvey/Weber DCOE mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between throttle bodies 2-3 is 93mm, however this can be adjusted if required (depending on your linkage).

This manifold is designed for the standard Weber/Jenvey DCOE mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between Bodies 2-3 is 102mm, however this can be adjusted if required (depending on your linkage).

Inlet Manifold to Suit Jenvey Throttle Bodies or Weber DCOE. This manifold is designed for the standard Weber DCOE Carb mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between carbs 2-3 is 93mm, however this can be adjusted if required (depending on your linkage).

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

If not specified we will automatically send out the 45mm. Check availability with our specialists. Add to Favourites.

TIG welded in aluminium and fully internally ground to ensure optimum flow and performance. This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage).

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 93mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold is designed for the standard Weber/Jenvey DCOE mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between Bodies 2-3 is 93mm, however this can be adjusted if required (depending on your linkage).

This manifold is designed for the standard Weber/Jenvey DCOE mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between Bodies 2-3 is 93mm, however this can be adjusted if required (depending on your linkage).

TIG welded in aluminium and fully internally ground to ensure optimum flow and performance. This manifold is designed for the standard Jenvey/Weber DCOE mounting and can be made with 40mm, 45mm or 48mm bore mounting plates.

This manifold is designed for the standard Weber DCOE Carb mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between carbs 2-3 is 93mm. Check availability with our specialists.

This manifold uses a specific plate that exactly matches the revised ports on this engine (larger and higher). This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 92mm.

This manifold is designed for the standard Weber DCOE Carb mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between carbs 2-3 is 97mm, however this can be adjusted if required (depending on your linkage).

This manifold uses a specific plate that exactly matches the revised ports on this engine (larger and higher). This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 92mm.

Specifically we needed trumpets to suit our popular GSXR throttle body kits for use on kit and modified cars - hence the 50mm bore to suit GSXR1000 tapered throttle bodies. danST Engineering 50mm Aluminum Spun Trumpet.

This manifold uses a specific plate that exactly matches the revised ports on this engine (larger and higher). This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 92mm.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold is designed for the standard Weber DCOE Carb mounting and can be made with 40mm, 45mm or 48mm bore mounting plates. The spacing between carbs 2-3 is 93mm, however this can be adjusted if required (depending on your linkage).

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold uses a specific plate that exactly matches the revised ports on this engine (larger and higher). This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 92mm.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 93mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

The spacing between carbs 2-3 is 101mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists. Add to Favourites. View Our Categories.

A SINGLE plate to suit the classic DCOE type mounting. Mild Steel (CNC Laser cut). Fastener holes are pilot drilled at 6mm to be drilled out to either M8 tapped or clearance holes. Add to Favourites.

TIG welded in aluminium and fully internally ground to ensure optimum flow and performance. This manifold is designed for the standard Weber DCOE Carb mounting and can be made with 40mm, 45mm or 48mm bore mounting plates.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 93mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold uses a specific plate that exactly matches the revised ports on this engine (larger and higher). This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 92mm.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 91mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 93mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.

This manifold is designed for the Jenvey 42mm 'SF' throttle body mounting. The spacing between throttle bodies is 90mm, however this can be adjusted if required (depending on your linkage). Check availability with our specialists.