LCD Display Modules

OLED display for Gotek Drive. Lower power consumption, better performance. Works very well with Flash Floppy firmware. Gotek Display Modification. Once your Gotek Drive has been upgraded with Flash Floppy or HxC firmware OLED display can be mounted.

Supports any revision For Raspberry Pi (directly-pluggable). Compatible For Raspberry Pi A, B, A+, B+, 2B, 3B, 3B+versions. The Pins that connect For raspberry pi must be correct. LCD Type: TFT. Size perfectly fits the Pi.

Simplify the circuit, this module directly into the Arduino sensor shield V5.0 sensor expansion board IIC device interface can. 2011 Latest Iic Lcd2004-Character LCD display module. Interface: I2C. 1 x LCD Display Module.

Ideal for the Arduino Card Module. Color: as shown in the photos.

1.8" ST7735R SPI 128 x160 TFT LCD Display Module Breakout For Arduino RPi etc This lovely little display breakout is a great way to add a small, colourful and bright display to any project. The 1.8" display has 128x160 colour pixels.

Designed for Raspberry Pi, easy to use. Support computer WIN7/WIN10(Touch cann't work at computer but work well at Raspberry Pi). Provide driver. Support HDMI output, audio output. 1 x HDMI connector.

OLED display, no need backlight, self-illumination, the display performance is better than the traditional LCD display, also lower consumption. Gotek Display Modification. If you have the Flash Floppy or H & C filmware installed you can add this display. Many install guides on the Web Driver IC: SSD1306 Size: 0.91 inch OLED Resolution: 128 x 32 IIC interface Display Color: white Pin Description: GND: Power Ground VCC: Power + (DC 3.3 ~5v) SCL: Clock Line SDA: Data Line.

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2.4″ diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)!

It is the best solution to replace the traditional LCD and LED Nixie tube. With the software - Nextion Editor (Official Download), users are able to create and design their own interfaces for Nextion display.

Provide 12 examples for Arduino and 3 examples of STM32. 3.5in 480x320 TFT LCD screen, high quality image display and wide viewing angle. Screen Material: TFT. Equipped with SD card socket and SPI FLASH circuit.

HDMI+VGA+2AV Driver Board Input Signal: HDMI VGA AV. 1 x HDMI+VGA+2AV Driver Board. Display mode: Normally White, Transmissive. 1 x 28cm 10 Pins Cable. 1 x 7" TFT Hig-Resolution Display Module. Remote: Optional.

Compatible for raspberry B+ motherboard and raspberry B motherboard. Support access to for raspberry pie B/B+, save the bulky HDMI display. Not include for raspberry board and other accessories, only display and shell boxes.

There are 16 LED’s mounted as a bar graph plus 4 more indicators. Demo firmware and schematic is available on Github, just search for the user mottramlabs. A one line 4 digit display using a MAX7219 display driver.

This is a very popular LCD Keypad shield for Arduino and other variants. Pins 4, 5, 6, 7, 8, 9 and 10 are used to interface with the LCD. Just one Analog Pin 0 is used to read the push buttons. 4 channel 12v/24v to 5v input optoisolator optocoupler for Arduino RPi ARM PIC.

HDMI+VGA+2AV Driver Board Input Signal: HDMI VGA AV. 1 x HDMI+VGA+2AV Driver Board. Display mode: Normally White, Transmissive. 1 x 28cm 10 Pins Cable. 1 x 7" TFT Hig-Resolution Display Module. Audio: Support.

Resolution: 480x320. 1 x LCD Module. Support touch screen function. The colors may be a little difference for the different monitor display. Designed with a TF (Micro SD) card socket on the back of board so that you can conveniently insert a card.

Used for Raspberry Pi 3/2 or Computer display. Signal input: 2 AV + VGA + 1 channel HDMI high-definition reversing HDMI input: Version HDMI 1.2. 1 pcs x LCD Screen. Support image up and down left and right flip, image 4: 3/16: 9 display format conversion.

Touch type: Resistive touchscreen. A HDMI cable is needed for Raspberry Pi 1B. Product type: Touch Screen for Raspberry Pi. High resolution up to 1024 600 gives HD pictures. 1 Touch Screen for Raspberry Pi.

Supports analog SPI and hardware SPI. Designed with one socket for sd card. 5V compatible, use with 3.3V or 5V logic. Driver IC: ILI9341. Resolution: 240x320. 4 channel 12v/24v to 5v input optoisolator optocoupler for Arduino RPi ARM PIC.

Nextion includes a hardware part (a series of TFT boards) and a software part (the Nextion editor). The Nextion TFT board uses only one serial port to communicate. It lets users avoid the hassle of wiring.

84x48 Display Matrix. • RST:Reset. • CLK:Serial Clock Line.

1602 16x2 LCD KEYPAD Display Screen Module BLUE Serial Arduino Raspberry PI. This is a very popular LCD Keypad shield for Arduino and other variants. Pins 4, 5, 6, 7, 8, 9 and 10 are used to interface with the LCD.

This module is ideally suited to adding a colour screen to your project. This is the ST7735 based 128x160 full colour TFT LCD module. The module also features a SD card slot on it's reverse side. In combination this makes a powerful module that can be used for displaying all manner of pictures and data while storing and retrieving information over a longer period.

Internal Power Supplier with Universale / Auto Sensing AC90 to 260V 50 / 60Hz. Optional to Built-in Touch Screen for Interactive Appliction. Cell Type / Glass Surface - TFT LCD / Black Anti-Galre, Low Reflection Coating.

1PCS 84 48 LCD Module blue backlight adapter pcb for Nokia 5110. RST - Reset. VCC - power input (3.3v or 5v). GND - Ground. CLK - Serial Clock Line.

This is an I2C version and works using only 4 wires VCC GND SDA and SCL. Hence more expensive than the basic HD44780. The I2C interface is provided and already fitted. I2C interface includedand fitted (already soldered).

1PC 128x64 Blue LED display module for Arduino. Interface type is IIC. Fully compatible with Arduino, 51 Series, MSP430 Series, STM32 / 2, CSR IC, etc. Note: The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.

It is another great blue backlight LCD display. However, with this I2C interface LCD module, you will be able to realize data display via only 2 wires. If you already has I2C devices in your project, this LCD module actually cost no more resources at all.

Jake Walker's ST7735 Raspberry Pi Blog ', which provides a very comprehensive explanation on how to use these screens. The Arduino code example below provides a simple test to get this TFT screen up and running.

CHARACTER GENERATOR BUILT IN. DATA INTERFACE PARALLEL 4 OR 8 BITS. CHARACTER FORMAT 5 X 7 DOTS AND CURSOR. CHARACTER SIZE 3.2 X 5.55MM. DOT SIZE 0.6 X 0.65 MM. VIEWING AREA 154.4 X 15.8 MM. FRONT SURFACE GLOSSY.

1.5" 128x128 SPI Full Colour SSD1351 OLED Display Module. 1.5" SSD1351 Screen. 1 x 1.5" 128x128 SSD1351 Full Colour OLED Display Module. You may also find the '1.5" OLED Display Datasheet ' link helpful.

Support computer WIN7/WIN10(Touch cann't work at computer but work well at Raspberry Pi). Designed for Raspberry Pi, easy to use. Provide driver. Support HDMI output, audio output. 1 x HDMI connector.

Used for Raspberry Pi 3/2 or Computer display. Signal input: 2 AV + VGA + 1 channel HDMI high-definition reversing HDMI input: Version HDMI 1.2. 1 pcs x LCD Screen. Support image up and down left and right flip, image 4: 3/16: 9 display format conversion.

<p>10 Inch LCD (POS) Advertising Screen with Motion Sensor. Condition is New. Dispatched with Royal Mail 2nd Class.</p><p>3M long 12v power supply</p><p>Video player</p><p>Play from memory card USB host</p><p>Auto play picture/photo/music</p><p>Auto repeat:Display all pictures and videos in a loop automatically </p><p>Support 720p video content file</p><p>Support multiple file format: PICS: JPG WMA MP3 MPEG 1/2/4 </p><p>Support SD/USB Memory card</p><p>Timer function: Auto power on/off</p><p>Power consumption: 110-240v AC/DC 5V 1.5A (12V 1.5A can be optional)</p><p>Remote control</p>