Ideal 079716 PCB 25d Printed Circuit Board

kitchen29 (59616)
99.9% positive Feedback
Price:
£59.99
Free delivery in 1-2 days
Estimated between Wed, 23 Jul and Thu, 24 Jul
Returns:
60 days return. Buyer pays for return postage. If you use an eBay delivery label, it will be deducted from your refund amount.
Condition:
New
Elan 2 NF 280 - 41-429-64. Classic Slimline FF 350 - 41-392-04. Classic Slimline FF 340 - 41-392-03. Classic Slimline FF 330 - 41-392-02. Classic RS3 60 - 41-392-12. Classic RS3 50 - 41-392-11. Classic RS3 40 - 41-392-10.

About this product

Product Identifiers

BrandIdeal
MPN079716
eBay Product ID (ePID)1619706228

Product Key Features

Power SourceCorded Electric
FeaturesElectric, Programmable
Heating SystemBoiler
Mounting LocationWall

All listings for this product

Buy it now
Any condition
New
Pre-owned

Ratings and reviews

4.7
12 product ratings
  • 10 users rated this 5 out of 5 stars
  • 1 users rated this 4 out of 5 stars
  • 0 users rated this 3 out of 5 stars
  • 1 users rated this 2 out of 5 stars
  • 0 users rated this 1 out of 5 stars

Would recommend

Good value

Good quality

Most relevant reviews

  • Ideal classic slimline 250ff

    Replacement PCB for a 15year old boiler which would not ignite the pilot light. Took less than 30 minutes to replace. Like for like connectors made reconnecting simple. Old PCB had an earth and neutral plug connector but replacement PCB came with ready soldered earth and neutral wires. This proved not to be an issue with the Earth wire going to boiler casing, and the neutral wire going to the neutral terminal of power terminal block. If I had any criticism, it would be that the neutral wire is too short and hinders the re assembly of the boilers lower control panel. This was a reconditioned PCB but looked aesthetically like a new unit. Switched boiler back on after fitting replacement PCB and the boiler fired up first time.

    Verified purchase: YesCondition: Pre-owned

  • Perfect replacement PCB for an Ideal Classic 250 FF

    I fitted it in less than an hour. All of the existing connectors just slid into place with no problems at all. The neutral lead was in a different place to my old board but it was obvious where it needed to be fitted to. Turned the power back on and away everything went. Marvellous! Expert quoted me £260 to do the job. It cost me £69 and an hour of my time. Try them, excellent quality gear.

    Verified purchase: YesCondition: New

  • Fiddly but great and easy repair

    took time locating and memorising which sockets went where recommend draw a simple diagram with wire colour and number of pins in plugs, It was then a simple job to install and all worked perfectly when switched back on. Well pleased

    Verified purchase: YesCondition: Pre-owned

  • Printed circuit board

    Magic worked a treat,very easy to fit

    Verified purchase: YesCondition: Pre-owned

  • Excellent for the price

    Great condition and well worth it .

    Verified purchase: YesCondition: Pre-owned

  • Good value

    It comes with all the wires and connectors

    Verified purchase: YesCondition: New

  • .

    did the job

    Verified purchase: YesCondition: Pre-owned

  • Highly Recommend

    Excellent service and works very well

    Verified purchase: YesCondition: Pre-owned

  • great

    Easy to install, works perfectly

    Verified purchase: YesCondition: New

  • Ideal PCB

    Good spares

    Verified purchase: YesCondition: Pre-owned