CURRENTLY SOLD OUT
About this product
Product Identifiers
BrandRobertshaw
MPN41-205
UPC0662013283247
Model41-205
eBay Product ID (ePID)1637480480
Product Key Features
Power SourceElectric
Suitable ForConvection Oven/Stove, Convection Microwave Oven
Compatible BrandRobertshaw
ColorSilver
Item Depth3.31 inch
FeaturesHigh physical and thermal strength, Easy mounting, Silent ignition
InstallationBuilt-In/Integrated
MaterialStainless Steel
TypeIgniter
Dimensions
Item Height6.06 inch
Item Width3.15 inch
Item Weight3.84 ounces
Additional Product Features
Set IncludesPorcelain nuts (2)
Ratings and reviews
Most relevant reviews
- 11 Dec, 2019
Recommended
Good, I have broke one b4. Handle them extremely gently and do not touch the sensitive element. Do not jar it, easy does it.. I cut my wires a little too short, make sure you give yourself enough length , and lastly, pull on your wire nuts to make sure the wire is holding good on those ceramic nuts. Think it through and take your time.
Verified purchase: YesCondition: New
- 21 Dec, 2019
An easy to install igniter that does its job!
This is a gas oven igniter that I purchased to replace a failing igniter in a Maytag oven range. The build of this igniter as compared to the original seen pretty much identical, and it works like a charm once installed. Swapping out the old one for this new one is quite simple, which I will detail here. First and most important step: UNPLUG the oven! After that, you simply remove all of the racks from the oven, then undo and remove the oven's floor (it may be screwed down), which gives you access to the gas burner assembly.. Typically these igniters are held on by two screws that hold the igniter close to the gas burner; you really can't miss it. PRO TIP: It makes disassembly easier if you take off the oven door. It's quite easy to do on these models, simply open the door about 4 inches, and then pull straight up. The door will slide off of its hinges, no unbolting of screws needed. Once you locate the old igniter, simply unbolt it and pull it away from the burner, pulling the wires a few inches out of the back wall of the oven. After that, just snip the wires off of the old igniter (cut close to the old igniter body) and then strip a little bit of insulation off of the old wires. You then use the included ceramic wire nuts to connect the ends of the wires from the new igniter to ends of the old igniter's wires. It doesn't matter which wires you connect, so long as you are connecting an old wire to a new wire within each wire nut. After that, you tuck the excess wire out of the way behind the back wall of the oven, and then bolt the new igniter back onto the burner assembly. Then you put your oven back together by replacing the floor of the oven, the racks, and the door.. If you did everything correctly, after plugging the oven back in and turning on the oven, you should see the igniter start to glow and hear a flame come on in about 20 seconds. I've purchased a few of these igniters and each time it's a straightforward repair that takes less than 15 minutes.Verified purchase: YesCondition: New
- 27 Nov, 2019
New life for old Oven
I used it to replace a slightly different version and it worked perfectly. As long as the ratings are the same and the leads (wires) are long enough it's fine. Go to the Robert Shaw site to compare. The mounting holes were slightly different but I made it work without any drilling etc. The oven I was working on had been hacked before and so nothing was original. Be sure the ignitor is mounted so that it's not going to get banged into (they are fragile) and it's close enough to the burner element. If your oven goes "whoosh" when it lights the ignitor may be too far from the burner element. Most of the time you can simply bend the mount slightly to adjust. Being too far from the burner causes premature failure. The NLA Caloric part was almost $100 this was less than $20...Verified purchase: YesCondition: New
- 29 Apr, 2018
An oven igniter gets weak over time through heat cycles. Keep an extra on hand.
Even though the glow plug ignition on your oven may be glowing red and appear to be working, it may be weak & insufficient to ignite the burner. As a result the gas safety valve will stay closed and not allow the range to heat up. The original in most cases is hard wired hence the ceramic nuts included in the aftermarket replacement kit. Make sure when cutting and connecting wires to keep as much of the existing heat wire insulation as possible close to the wire nut connection. (Even if slightly bunched up). Only use just enough exposed wire to twist the two together to properly tighten the wire nuts. You do not want a chance of an electrical arc since typical forms of wire insulation cannot be used for this application. (i.e. heat shrink tubing, electrical tape, etc.)Verified purchase: YesCondition: New
- 30 Jun, 2021
Robertshaw quality
This is a great we'll made Robertshaw product that is made in the USA. Many other ignitors fail to list the country of origin and I was tired of replacing the ignitor every 9-12 months. Glad to have found this source.Verified purchase: YesCondition: New
- 18 Nov, 2020
Perfect replacement for Viking VGIC305
My Viking VGIC 305 igniters died after 19 years. OEM replacements are $160 each and I needed 3 igniters - 2 oven, one broiler. For $45 I bought three of these made in USA replacements and they work great. Oven heats great, broiler is like new. Excellent product!Verified purchase: YesCondition: New
- 27 Sep, 2019
Great replacement igniter
Easy quick install, comes with everything you need and works perfect. High quality materials and craftsmanship.Verified purchase: YesCondition: New
- 11 Nov, 2020
Oven is ready for Thanksgiving
Found igniter for my moms oven sent a question about igniter with model number and actually was directed to a better fitting igniter, shipping was quick, i installed it and it works perfect fixed the problem, install was fairly easy after viewing a YouTube video on my Frigidaire model. ThanksVerified purchase: YesCondition: New
- 21 Jan, 2020
Easy Fix
Not a lot to say about this simple part: Exact fit, trusted brand. Oven works like new again. Installation was quick and easy using basic hand tools.Verified purchase: YesCondition: New
- 17 May, 2017
Perfect.
Saved me lots of money, just cutting and splicing the wires rather than paying quite a bit more just to be able to remove the part and plug in. Having no experience doing this sort of thing, I found it easy enough and I was thrilled it worked!Verified purchase: YesCondition: New
