About
All Feedback (228)
- a***t (393)- Feedback left by buyer.More than a year agoVerified purchaseGreat ebayer. Had to cancel item through no fault of seller and they were extremely helpful. Responded to my message and refunded within 10 minutes. Highly recomend. Very helpful. Thanks!!
- .***e (249)- Feedback left by buyer.More than a year agoVerified purchaseProbably the best ebayer I've ever purchased from. Sent me a second item free of charge because they weren't happy with the quality of the one sent first. I wouldn't have know any better so thank you for your honesty. I wish you all the success in the future.
- o***o (1340)- Feedback left by buyer.More than a year agoVerified purchaseArtikel wie beschrieben und super schnelle Lieferung.
- r***o (2376)- Feedback left by buyer.More than a year agoVerified purchaseGreat seller, Great product ,A+ Thanks!!!
- k***n (955)- Feedback left by buyer.More than a year agoVerified purchaseDanke für die schnelle Bearbeitung.
- k***y (356)- Feedback left by buyer.More than a year agoVerified purchasePasst mit einer Lage Klebeband recht gut.
Reviews (2)
17 Sep, 2017
That's how it should have come from the factory
2 of 2 found this helpful I don't know who was the smart guy to design the throttle actuator that is exposed to oil, soot and high temperatures with plastic gears, but this kit lets you fix this for good.
I have a 2008 Audi A4 3.0 TDI and I have replaced 3 throttle bodies over the course of 5 years, I also tried 3D printed gears, but they didn't last long. I was so glad when I found this kit. The brass gears are machined very nicely, they look exactly like the plastic ones they are replacing and they look like they will last for the lifetime of the vehicle. The fit is very tight and accurate. I had to use a 5 mm drill to clean the bore of the round gear to make it slide on easier.
They include a set of high quality Mannol epoxy glue to glue the arced gear to the metal part it screws to. I think it would work without the glue with just the screws, but with epoxy it will be a permanent bond.
The hardest part was removing the old plastic arced gear that is molded onto a metal base. I used wire snips and long nose pliers for that. Once that is done, you should do a test fit without the glue to see if everything fits fine. Then mix up the glue and assemble everything with glue applied. The glue will take 24 hours to fully cure, but it starts hardening in 4 minutes, so be quick.
Put it back into the car, did not have to relearn anything, it worked straight out of the box. All in all, great kit.
04 Jan, 2017
The only kit you need for working with silicone
2 of 2 found this helpful Working with silicone is notoriously messy and I have often postponed it to the last moment or tried to avoid it altogether. Techniques I've used in the past were sticking masking tape, wetting a finger in a dishwasher solution, different kinds of applicators, but the results were rarely satisfactory. The silicone didn't stick evenly, edges would sometimes peel, mold would form underneath, the caulking line would be of different width every time, etc.
This kit changed everything - there is no need to use masking tape, the bead profile is always the same and the best addition are those black guide rails - they allow you to slide the tool along a tiled wall and not create an indent every time the applicator hits the grout. It does take some practice to master it, but the results are always consistent and just great. If you mess up in a place, you can just clean it and redo it before the silicone started to set.
By the way it works just as well for other types of sealant, including acrylic or even construction glue.
It is not the cheapest kit out there, but it's the only one you will need. Comes in a nice box with an instruction leaflet. And make sure you watch the tutorial videos on YouTube.