- All
- New
- Pre-owned
5stars
225ratings4stars
48ratings3stars
31ratings2stars
25ratings1star
35ratings
324 reviews
Does the job
Watched U tube video and took a chance. Happy with the product but it's not quite as easy to use. As demonstrated but I was able to fully load Glock 9mm mags with a bit of effort. Postage is very high though.Read full review
Verified purchase: Yes • Condition: new • Sold by: southwest217
Works good for factory boxed ammo
This works great on factory boxes ammo! Only reason I’m not giving it five stars is if you reload ammo the hard plastic boxes most use for reloads don’t hold the ammo firmly enough to pick up with the loader. Not really the fault of the loader just the facts, in my situation. Must transfer reloaded ammo to old factory tray.Read full review
Verified purchase: Yes • Condition: new • Sold by: luxemarkets
It works. By the original, not a knock off.
It works. I tried it on single-stack and double-stack 9 mm magazines in three different brands of pistols. if you’re loading 17-round magazines or higher, for example, it will get pretty tight toward the end of the push-down cycle. I find it works better as suggested if you push the magazine bottom against your belly and pull the loader top piece toward you. I would not buy a cheap knock off. Get the original, ETSRead full review
Verified purchase: Yes • Condition: new • Sold by: thefalco1
Good product, but very stiff
The product worked , but ..........it is very hard to push the rounds into the magazine. I did use the proper lightweight gun oil , but it took several attempts to load my .40 caliber magazine. I am assuming that the stiffness will eventually ease up with use. I would have given it a rating of 5 if there had not been so much force required to properly use the loader.Read full review
Verified purchase: Yes • Condition: new • Sold by: luxemarkets
Nice concept but...
Great idea but I tried several double stack and single stack magazines and I had to really push them hard to get them in. Once in I had to apply a great deal of pressure to jam the rounds down into the magazine. I pulled the magazine out and one round fell to the ground. Also noticed plastic bits and shavings on the magazine. One round had a dent in the brass. MAGPUL is STILL the leader in mag loaders.Read full review
Verified purchase: Yes • Condition: new • Sold by: gooutdoorgear
works for 9mm, can depend on ammo
Works for the factory 9mm ammo I have tried in both glock mags and a ruger sr9 mag (ruger pcc). It can be a little finicky until you figure out the proper technique, for me the ruger and glock mags needed different pressures applied to the mag itself. (glock mag resting on table, and plunger pushed down vs ruger mag just held in place, not really pushed into the loader)
I find that it also has to be one continuous motion, stopping partway through usually means having to restart from an empty mag.
One problem is it does not work at all for the cast reloads I made, probably because they are short (1.09" OAL due to the 356-125-2R bullet shape)
Once you figure it out it is fast, easy, and well worth it.
if you can not get it to work at all, it may be the ammo you are using.Read full review
Verified purchase: Yes • Condition: new • Sold by: szsuper789654
Good value when it comes to loading 9mm and 40sw mags.
Works good on standard pistol mags... as advertised. Does not work on extended pistol carbine mags such as the Colt SMG, UZI, etc. It is for 9mm and 40sw. Keep in mind, there are mag loaders out there that will do both calibers plus 45acp for only a couple extra bucks.Read full review
Verified purchase: Yes • Condition: new • Sold by: fuddlebucks
Works ok for most mags
It works ok. But you really have to push it hard to get it to work and smack the bottom of some mags to get all 10 in. It does work and does what it claims it’s just not as easy as the videos show. Much easier than loading by hand especially when your loading 6 mags At a tomeRead full review
Verified purchase: Yes • Condition: new • Sold by: jake754
Fantastic when you know how to use it.
The instructions for use need to be more complete and clear. Break in time and process needs more detail. The loading process needs more detail and pictures showing the correct angle necessary for the loader to function.
Help by the manufacturer was responsive.Read full review
Verified purchase: Yes • Condition: new • Sold by: konellz-tech
amazing product
I was skeptical, but have found that it works well with a number of magazines. Faster and easier than anything else I have seen.
But be sure you buy a brand name product. Not a cheap knock off.
Verified purchase: Yes • Condition: new • Sold by: reedraidersg